CPM 15V - Revision history

ThatWouter at 16:24, 12 October 2022

2022-10-12T16:24:22Z

← Older revision		Revision as of 10:24, 12 October 2022
Line 25:		Line 25:
	\|/		\|/
	\|/		\|/
			\|0.90
	\|/		\|/
	~~\|0.90~~
	\|/		\|/
	\|14.50		\|14.50

ThatWouter at 16:24, 12 October 2022

2022-10-12T16:24:02Z

← Older revision		Revision as of 10:24, 12 October 2022
Line 27:		Line 27:
	\|/		\|/
	\|0.90		\|0.90
	\|/
	\|/		\|/
	\|14.50		\|14.50
			\|-

	\|}		\|}

ThatWouter at 16:23, 12 October 2022

2022-10-12T16:23:48Z

← Older revision		Revision as of 10:23, 12 October 2022
Line 26:		Line 26:
	\|/		\|/
	\|/		\|/
			\|0.90
	\|/		\|/
	~~\|0.90~~
	\|/		\|/
	\|14.50		\|14.50
	\|-
	\|}		\|}

ThatWouter at 16:22, 12 October 2022

2022-10-12T16:22:54Z

← Older revision		Revision as of 10:22, 12 October 2022
Line 19:		Line 19:
	\|5.25		\|5.25
	\|/		\|/
	\|/
	\|/		\|/
	\|0.50		\|0.50
	\|1.30		\|1.30
			\|/
	\|/		\|/
	\|/		\|/
Line 35:		Line 35:
	From Spyderco's website:		From Spyderco's website:

	''~~CPM-M4 is~~ a ~~high-speed, wear resistant, tool steel. It is non-stainless steel. Its high~~ content ~~of Molybdenum and Tungsten gives it a fine grain size~~, ~~greater strength, hardness and toughness. It is a triple temper heat treat to make it as tough as possible without brittleness. The grinding combined with~~ the triple temper heat treating process can cause warping up to 50 thousandths (.050) of an inch which is not enough to affect the performance of the knife. CPM-M4 will provide high edge retention and impact resistance ~~with an Rc~~ of ~~58-63; you'll also find it's relatively easy to sharpen~~.''		''Boasting almost a 15 percent vanadium content, this remarkable material offers the highest wear resistance of any cold work tool steel available today.''

	[[Category:Steels]]		[[Category:Steels]]

ThatWouter at 16:20, 12 October 2022

2022-10-12T16:20:53Z

← Older revision		Revision as of 10:20, 12 October 2022
Line 15:		Line 15:
	{{Tableheading}}'''Tungsten'''		{{Tableheading}}'''Tungsten'''
	{{Tableheading}}'''Vanadium'''		{{Tableheading}}'''Vanadium'''
			\|-
	\|3.40		\|3.40
	\|5.25		\|5.25

ThatWouter: Created page with "CPM 15V consists of: {|{{Articletable}} {{Tableheading}}'''Carbon''' {{Tableheading}}'''Chromium''' {{Tableheading}}'''Cobalt''' {{Tableheading}}'''Copper''' {{Tableheading}}..."

2022-10-12T16:20:36Z

Created page with "CPM 15V consists of: {|{{Articletable}} {{Tableheading}}'''Carbon''' {{Tableheading}}'''Chromium''' {{Tableheading}}'''Cobalt''' {{Tableheading}}'''Copper''' {{Tableheading}}..."

New page

CPM 15V consists of:

{|{{Articletable}}
{{Tableheading}}'''Carbon'''
{{Tableheading}}'''Chromium'''
{{Tableheading}}'''Cobalt'''
{{Tableheading}}'''Copper'''
{{Tableheading}}'''Manganese'''
{{Tableheading}}'''Molybdenium'''
{{Tableheading}}'''Nickel'''
{{Tableheading}}'''Nitrogen'''
{{Tableheading}}'''Phosphorus'''
{{tableheading}}'''Silicon'''
{{Tableheading}}'''Sulfur'''
{{Tableheading}}'''Tungsten'''
{{Tableheading}}'''Vanadium'''
|3.40
|5.25
|/
|/
|/
|0.50
|1.30
|/
|/
|/
|/
|0.90
|/
|14.50
|-
|}

From Spyderco's website:

''CPM-M4 is a high-speed, wear resistant, tool steel. It is non-stainless steel. Its high content of Molybdenum and Tungsten gives it a fine grain size, greater strength, hardness and toughness. It is a triple temper heat treat to make it as tough as possible without brittleness. The grinding combined with the triple temper heat treating process can cause warping up to 50 thousandths (.050) of an inch which is not enough to affect the performance of the knife. CPM-M4 will provide high edge retention and impact resistance with an Rc of 58-63; you'll also find it's relatively easy to sharpen.''

[[Category:Steels]]